Welding Cable xlr GEFELL MV692

[melvins111]

Hello all.
I just got a microphone geffel mv692.
I have and its transformer connectors.
However, I miss a NS104 via XLR cable.
With it, how to proceed with welding?

Thank you for your help

[melvins111]

hello.

nobody could help me, I find it on the net

thank you

[melvins111]

hello,

I can not test the microphone if I did not connect a cable xlr.

Or find plans (schematics) for welding this one.

thank you again

[greg]

I'm a little unsure what you're asking, but I assume you are trying to build an adaptor to connect the original connector to a standard XLR. I googled "Gefell MV692 Schematic" and found this page. Both sets of schematics are there. It looks like you will have to do more than make an adaptor cable. There might be additional internal modifications. I recommend contacting Gefell directly to get the proper upgrade. They still support this mic.
Good luck,
Greg

[tarandfeathers]

Agreed. I had my 692 48 volted/XLRed by MTG a few years ago, couldn't be happier.

[melvins111]

thank you greg
it's not that.
Just how the welded wire

[greg]

I'm Confused then,
Please ask your question en français. Our international department (Gregoire) will help you.

[melvins111]

ok
je possède pour ce microphone le transformateur et le câble qui le relie.
il me manque l'autre cable qui se termine en xlr.
IL faudrais que je fabrique le cable qui relie le xlr. avec ceci que je possède:
http://cgi.ebay.fr/36-VEB-MIKROTECH-GEF ... 20c45a9723


je voudrais le souder et pas faire n'importe quoi.

je ne trouve pas de schéma sur le net.

Merci a tous

[gregoire]

Salut melvins111, si je comprends bien tu as le micro, le boitier d'alimentation, et le cable qui relie le micro au boitier d'alimentation. Il te manque donc le cable qui relie le boitier d'alimentation au XLR. C'est ça?

Dis moi si c'est ça et je vais traduire ton problème pour que les gens du forum puissent t'aider, merci et à bientôt!

Grégoire

[melvins111]

bingo, c'est exactement ça
il faudrais quer je sache comment souder le câble qu'il me manque.

Ps: desoler pour le non anglais et surtout grand merci a vous

[gregoire]

ok
je possède pour ce microphone le transformateur et le câble qui le relie.
il me manque l'autre cable qui se termine en xlr.
IL faudrais que je fabrique le cable qui relie le xlr. avec ceci que je possède:
http://cgi.ebay.fr/36-VEB-MIKROTECH-GEF ... 20c45a9723


je voudrais le souder et pas faire n'importe quoi.

je ne trouve pas de schéma sur le net.

Merci a tous

OK, so melvins111 has a MV692 with a power supply. He has the cable to connect the mic to the power supply and he is looking for a wiring diagram to make a cable from the power supply to an XLR connector. In order to do that, he has already bought a 7-pin connector that connects to the power supply.

Here are two things that I found online:
N692 manual
48V adapter wiring diagram (look at the very bottom of the page)

Greg Norman recommends that you contact Microtech Geffel directly so they can explain to you how to do that. Any help is appreciated!

PS: si tu as du mal à comprendre ma réponse en anglais tu peux m'envoyer un message perso en francais, à plus!

[Nate Dort]

I'm Confused then,
Please ask your question en français. Our international department (Gregoire) will help you.

In a surprising turn of events, Greg is the first to surrender.

[greg]

I'm Confused then,
Please ask your question en français. Our international department (Gregoire) will help you.

In a surprising turn of events, Greg is the first to surrender.

Actually,
Gregoire is acting as my avatar in this case. In a way, I am occupying him like the Nazis.
I should add, that the 48v mod is not the ideal way to go about using this mic. It will make sound, but probably have less current to work with than spec'ed for "T phantom" (which, only glancing I think it is). If he wants to use it with 48v phantom power, he should have Gefell mod the mic for him. Otherwise, he needs to find out which of the several output wiring schematics is right for him. So we need a German avatar now...

[melvins111]

I still did not test the microphone.
I find nothing on the internet.
here is a picture of the whole.

GEFELL MV692

GEFELL MV692.jpg (199.84 KiB) Viewed 1219 times

How to solder the two connectors under the arrow?

[greg]

Contact Microtech Gefell
http://www.microtechgefell.de/index.php ... etzgeraete
Click on Questions, and ask them...
Or do it on this page.
http://www.microtechgefell.de/index.php ... forms&id=1

Sorry I couldn't have been more help to you.

[gregoire]

Ok, so I had emailed Microtech Gefell about that a few weeks ago, and they responded today with the solution. Here is the drawing you need:


Let us know if it works!
Gregoire